Top 10 common forklift accidents ， forklift operation ought to take note of these matters ！.

Top 10 common forklift accidents ， forklift operation ought to take note of these matters ！.

Blog Article

Do not ignore the forklift at the office. If the operation is not good, there will certainly be significant mishaps in minutes, and there are lots of accidents involving forklifts.

Situation 1: The forklift freight blocked the vehicle driver's view, and the person in front might not be located, leading to a moving mishap.
Situation 2: In order to maintain the equilibrium of the forklift when raising heavy goods, the staff members used their body weight as the counterweight, which virtually created casualties.
Instance 3: The size of the forklift cargo surpasses the permitted width of the route and holds on the roadside shelf, which nearly causes an crash.
Case 4: Forklift is speeding up and surrender during a turn.
Instance 5: The forklift driver did not notice the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift lifts the personnel illegally, the forklift motorist does not wear the seat belt, the forklift lifter falls and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift vehicle driver did not put on a safety belt and fell from the car when it rolled over and was crushed.
Forklift procedure should pay attention to these matters ：.

Start.
1. Before beginning, observe the environments, and after verifying that there are no barriers that prevent the safety and security of driving, honk the horn initially and then start.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge must be risk-free prior to beginning.
3. When the forklift begins with a load, the chauffeur must first validate that the load is secure and trusted.
4. The start has to be sluggish and constant.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole ought to be tilted backwards. .
2. Do not lift the fork too high when driving. When entering and leaving the task site or while driving, take care that there will be no obstacles overhead. When the load is traveling, the fork must not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be reduced to the typical driving placement before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be provided first. High-speed doglegs are restricted. High-speed sharp turns will trigger the vehicle to shed lateral stability and topple. .
5. When the forklift is downhill, it is strictly restricted to shut off the flame and slide, and it is forbidden to brake suddenly while driving with tons unless there are unique conditions.
6. When the forklift is running, it should comply with the web traffic rules in the manufacturing facility and must maintain a specific security distance from the car ahead. .
7. When the forklift is running, the lots needs to remain in the lowest setting that does not impede the driving, and the gantry should be properly slanted back. The lots will not be raised other than when stacking or filling. .
8. The elevation of the lots should not obstruct the chauffeur's view. In special scenarios, when the item influences the forward vision, drive at a low speed when turning around.
9. It is forbidden to activate the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it needs to drive securely at a low speed when getting in the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to base on the fork to hold things and play a stabilizing duty. .
12. If problems are discovered, they will be repaired and reported in a prompt manner, and they will never ever run with diseases or conceal them.

loading and discharging.
1. When fork-loading things, the distance in between the two forks ought to be readjusted as required to make the tons of the two forks well balanced and not manipulated, and one side of the product ought to be against the rack. .
2. It is prohibited to work with a solitary fork or use a fork top or pull. In unique scenarios, safety indication need to be set up to remind bordering pedestrians. .
3. In the process of filling and unloading products, the forklift needs to be braked with the brake. .
4. The rate of the vehicle should be slow-moving and stable. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled items and injure individuals. .
5. When making use of a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be kept in mind that the fork pointer must not touch various other goods or objects. The tons ought to be maintained with marginal back tilt of the gantry to make sure that the load does not glide backwards. The pole can be tilted forward slightly when the load is lowered to permit very easy placement of the load and extraction of the forks. .
6. It is restricted to fork items at high speed and hit difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so as to prevent the collapse of the goods and hurt people. .
8. Straining is restricted, and it is forbidden to utilize forks to raise workers to participate in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slip, place, round or roll items. .
10. It is not permitted to utilize forks to pick, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should unload the goods or reduced the fork frame.
2. Pull the hand brake handle to dead or depress the emergency brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance ought to be checked, and fuel, lubing oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance Stand-on Electric Pallet Stacker driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with Electric Forklift Truck for Warehouse forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844